Hinode

Universal hub puller kit with hydraulic ram giving up to 12 tons of pressure with a large slide hammer assembly
The kit greatly simplifies the removal of the wheel hub and release of the drive shaft without damaging the fine threads on the shaft through hammering
Use on GM, VAG, PEUGEOT, CITROEN, RENAULT, FORD and VOLVO etc

For removing and installing the transmission clutch piston snap ring
Adjustable for most models of European, Japanese and American cars and light trucks

The tool set can remove install FM / FM12 / FH truck injector sleeve
Suitable injector sleeve genuine no.: 85124276, 85104134, 21515329
Application : VOLVO (FM / FM12 / FH) truck
This tool needs to combine with YM1902

Apply the adhesive around the fine threads on the transparent chamber
Connect the transparent chamber to the upper funnel part to form a complete funnel
Twist type adapter fits the most recent VAG
Clip type adapter fits BMW, MERCEDES, VAG
Knob type adapter fits VAG 1.5 petrol engines

Introduction: 
The timing adjustment and the overhaul application involving front end, the gear, the timing chain, etc
Require removal of front timing chain cover, and remove that, the crankshaft pulley must be removed, on most variants of the pulley bolt have a very high torque specification, and removal or installation of this pulley requires the special remover and the holding tool
Application: 
Crankshaft pulley holding tool must be removed for the engine over¬haul application / removal of front timing chain cover

Contents :
Professional and damage-free removal of ignition coils and ignition coil strips on VAG and OPEL / VAUXHALL engines
2 ignition module pullers for: CHEVROLET / GMC Aveo Cruze, OPEL / VAUXHALL 3 and 4 cylinder petrol engines with fuel injection 1.0 - 1.2 - 1.4 - 1.6 - 1.8 - 2.0 - 2.2 l engines as well as FIAT Croma 1.8 l ALFA 159 1.8 l recommended use in pairs
4 ignition claws:
Type A: VW GOLF, BORA, BEETLE, LUPO, PASSAT, TOURAN, T4, AUDI A2
Type B: BORA, GOLF, PASSAT, SHARAN, TOUAREG, PHAETON, T5
Type C: 8 and 12-cylinder engines such as Phaeton, among others
Type D: direct injection engine VW GOLF, TOURAN, PASSAT and eos as well as AUDI A4 and A6 etc

Suitable for TESLA MODEL X & S

Suitable for CHEVROLET BOLT EV, TESLA MODEL 3 & Y

Tool precisely-made with slots to mesh with the ribs on fuel pump locking rings for TOYOTA and LEXUS
Elevated bridge to avoid blockage from connectors and lines on fuel pump
Helps remove and install the fuel pump locking rings easier and faster
3/8" square drive - 19 mm hex
OD 177 mm / 7 inch - ID 143 mm / 5.6 inch

With hexagon drive SW 30
For the dismantling and assembly of the rear axle nut
High accuracy of fit
Robust execution
Suitable for high tightening and loosening torque
Application range: 
MERCEDES BENZ CITARO
ZF AV 133 REAR BUS

Designed for use on truck tractor differential main axle

Application: BENZ 2544

RENAULT, VOLVO, FIAT models

RENAULT, VOLVO, FIAT, DAF models

The joint screws into the suspension arms so is only removed from the top
This tools can removed it with independent from suspension with top and bottom wishbones
Application: VOLVO B12 (2006 onwards)

This is the newly revised installation tool for the stainless conical cups 85137065

Applications include Volvo trucks

Buick century:1997-2002 buick 
Buick lesabre:1996-1999
Buick park avenue 1996-2004
Buick regal 1996-2004
Buick riviera 1996-1999
Chevy impala ss2004
Chevy monte carlo ss2004
Oldsmobile eighty-eight 1996-1999
Oldsmobile LSS 1996-1999
Oldsmobile refgency 1996-1999
Pontiac bonneville 1996-2003
Pontiac grand prix 1997-2006

This helpful puller will handle a variety of injectors found in cummins engines; mechanical L-10, PDT and PTD top stop 855NH
Its two jaw design firmly grips the injector while it is being removed by the slide hammer
Includes: special adapter for pulling STC injectors
OEM NO: OTC-5042

Sharp,hardened steel blades remove carbon, old gasket material, sludge and other hard-to-clean substances
Comes complete with three blades

Suitable for MERCEDES-BENZ engine: OM 654 E-class type 213
Easy installation on the engine of the vehicle

Suitable for MERCEDES-BENZ engines:
M270 A-class model 176  
B-class type 246
M271 C-class model 203, 209, 204  
E-class model 211, 212, 207 - SLK model 171, 172  
Sprinter model 906
Easy installation on the engine of the vehicle

Suitable for engines:
MINI: N47C16A - N47C20A
CITOROËN: 1.6,1.6 16V, 2.0 16V
PEUGEOT: 1.6, 1.6 16V, 2.0 16V 
Easy installation on the engine of the vehicle

Suitable for engines:
FORD: 1.4, 1.6, 2.0 and 2.2 TDCI, 
TOYOTA: Aygo 1.0 and 1.4 HDI, 
CITROËN: 1.9D, 1.9 TD, 1.4, 1.6, 2.0 and 2.2 HDi ∙ 1.4 and 1.6 16V HDi
FIAT: 1.6 D, 1.9 D and 2.0 JTD, 2.0 JTD 16V, 2.2 JTD
PEUGEOT: 1.4, 1.6 , 2.0 and 2.2 HDi, 1.9 D, 1.6T HP
Easy installation on the engine of the vehicle

Suitable for engines:
OPEL, RENAULT: G9Q-T-U
NISSAN, OPEL, FIAT, RENAULT: R9M
MERCEDES-BENZ: C-Class model 205, GLC model 253 with OM 626, Vito model 447 with OM 622
DACIA: H5F - K7M - K9K - K4M - D4F - K7J - K4M - H4B - D4F
Easy installation on the engine of the vehicle

Suitable for 1.5 TSI VW Group engine
AUDI A1  (2018 -newer), A3 (2017 - newer), Q2 (2018 - newer), Q3 (2018 -Newer).
SEAT ARONA (2017 - newer), IBIZA (2017 - newer), LEÓN 3 (2018 - newer), TARRACO 2018 - newer) ATECA (2018 - newer)
ŠKODA KAROQ (2017 - newer) OCTAVIA 3 (2017 - newer), SUBERB 3 (2018 - newer).
VW ARTEON (2018 - newer), GOLF 7 (2017 - newer) GOLF SPORTSVAN (2017 - newer), POLO 6 (2017 - newer), T-ROC (2017 - newer), PASSAT B8 (2018 - newer), TOURAN 2 (2018 - newer)

HONDA K-series cam lock pin tool
This speciality HONDA tool inserts into the camshaft pulse plates and locks the cams in place for timing chain alignment

Specially designed for plastic oil filter cap of TOYOTA / LEXUS
Material : aluminum
Size: 3/8" DR X 64.5 mm X 14 pt 
Applicable：
TOYOTA: 3.5 L since 2007 
LEXUS: IS250, IS350, GS300, GS350, GS450HE, S350, RX350, LS460, LS600H

Quickly disconnects electrical connectors without damage
Long claw can reach deep places
Releases locking tabs on electrical connectors, component connections and wiring harness connectors
The safe and easy way to remove small, thin or recessed connector that's difficult to work with

Quickly disconnects electrical connectors without damage
Special angle can avoid obstacles
Releases locking tabs on electrical connectors, component connections and wiring harness connectors
The safe and easy way to remove small, thin or recessed connector that's difficult to work with

The wrench set is designed to service the diesel filter / sensor on MAZDA SKYACTIV-D2.2 (SH-VPTS & SH-VPTR) engine
Suitable for 2.2L diesel : CX-5 / CX-8 / MAZDA 6 (ATENZA) / MAZDA 3 (AXELA)

Use the disconnect tool to squeeze the release tabs and release the quick-connect fittings
Suitable for GM, OPEL, HOLDEN, FORD, CHRYSLER, MITSUBISHI
Fit the various norma quick connector sizes: 1/4”(black),  5/16”(red),  3/8”(blue)

Multiple uses clamps panels in place for welding and panel bonding
Small profile allows door to be closed for alignment check before welding

Is able to chose saw : 18T(red) , 24T(sliver) , 32T(black)
Blow per min : 7000 BPM
Stroke length : 10 MM
Cutting capacity : 3.0 MM
Air inlet : 1/4”
Vibration : 16.988M/sec
Sound power level : 89.3dBA
Sound pressure level : 100.3dBA
Average air consumption :  4 CFM(28SCFM)
Weight : 2.43 LBS (1.1KGS)
Length : 10.51" (267 mm)

Use with the BN0216
Includes: 4 red plastic sleeve, 6 pins and adhesive
Adheres pin to the chinaware for easy extraction without cylinder damage
Includes red plastic sleeve to remove stuck electrode shield

Revised to include FORD / LINCOLN plastic oil pan drain plugs of engines: 2.7 L / 2.7 L (2018) / 3.0 L / 3.3 L / 3.5 L turbo from 9-12-2018 / 5.0 L (2018)
Traditional tools can cause harm and waste time
The adapters will not harm drain plugs and are designed to slot in and easily discharge these plugs
Include tool and adapters to dismantle plastic oil pan drain plugs establish on many late model FORD, VOLKSWAGEN, AUDI and BMW vehicles

Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement
On 2500 and 3500 pickups, remove metal spring-loaded inspection plate on the bottom of the transmission 
Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel
On 4500 and 5500 trucks, remove the rubber inspection cap on the bottom of the transmission, insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place

Single hex hub nut socket 36 mm applications include FORD ka and fiat 500
Thin walled providing better access 78 mm long with 1/2" Dr
Manufactured from chrome vanadium

Used to remove / install final drive propeller shaft nut
Applications: BMW 
E90 - 335d, 335i, 335ix
E91 - 335d, 335i, 335ix
E92 - 335d, 335i, 335ix
E93 - 335i
E70 / F01 / F02 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F15 / F16 / F18 / F20 / F21 / F22 / F23 / F25 / F26

Features: 
Used to set camshaft timing
Application: PORSCHE 996420, 997, 911 BJ 98 -, 996 Turbo, BJ 01 - 05, 997 TT, GT2, BJ 07 - 09 
OEM Ref: 9661 (adjusting device), 9661/1 (holding keys - 4 pcs), 9401